FREE Shipping On Order Over 80$

Clemco SFD Clemlite Silicon-Carbide Lined Long Venturi Style Flanged Thread 1-1/4 inch Entry Metal Jacketed Sandblast Nozzle
Clemco SFD Clemlite Silicon-Carbide Lined Long Venturi Style Flanged Thread 1-1/4 inch Entry Metal Jacketed Sandblast Nozzle

Clemco SFD Clemlite Silicon-Carbide Lined Long Venturi Style Flanged Thread 1-1/4 inch Entry Metal Jacketed Sandblast Nozzle

Regular price
$257.00
Sale price
$257.00
Shipping calculated at checkout.
Quantity must be 1 or more


SFD Clemlite Silicon-Carbide Lined Long Venturi Style

Blast nozzle with long venturi shaped Clemlite® silicon carbide liner, metal jacket. Thread size and entry dimensions vary with nozzle series.

Purpose

A blast nozzle accelerates the air and abrasive as the mixture exits the end of the hose. The taper and length of the nozzle's inlet and outlet determine the pattern and velocity of the abrasive exiting the nozzle. The composition of the liner material determines its resistance to wear.

Requirements for Operation

Nozzles are sized by the diameter of their orifices in 1/16-inch increments. A No. 2 nozzle has a 2/16-inch (1/8-inch) orifice, a No. 3 nozzle has a 3/16-inch orifice, etc. The size of the nozzle orifice determines abrasive and air consumption. Air consumption is measured in cubic feet per minute (cfm) at a given pressure. See the air and abrasive consumption chart on the back of this page.

When choosing a nozzle, consider the amount of available air in cfm, the capacity of the blast machine and the inside diameter of the piping, and the blast and air hoses. For optimal performance, these
elements must be compatibly sized. See the chart on the back of this page.

If too large a nozzle is used, low blast pressure and rapid wear on the blast hose will occur. If too small a nozzle is used, smooth media flow will be difficult to achieve.

Description of Operation

The operator inserts the nozzle washer into a contractor-thread nozzle holder and screws in the nozzle, turning it by hand, until it seats firmly against the washer.

With all related equipment correctly assembled and tested, the operator points the nozzle at the surface to be cleaned and presses the remote control handle to begin blasting. The operator holds the nozzle
18 to 36 inches from the surface and moves it smoothly at a rate that produces the desired cleanliness. Each pass should overlap slightly.

The operator must replace the nozzle once the orifice wears 1/16-inch beyond its original size.

Advantages

  • Expected life with expendable abrasives is up to 500 hours
  • Durable metal jacket
  • Non-binding contractor threads
  • 42% lighter than tungsten carbide

Note: Best performance is obtained when sizes of nozzle, blast machine piping, blast hose and air hose are properly matched

  • Cfm range is based on blasting at 100 psi for the life of the nozzle.
  • Blast machine capacity should allow 20 to 30 minutes of blasting.
  • Hose ID should be three to four times the size of the nozzle orifice

Chart shows air consumption in cubic feet per minute (cfm), abrasive consumption in pounds per hour and cubic feet per hour for abrasives weighing 100 pounds per cubic foot, and compressor horsepower (hp) based on 4 to 4.5 cfm per horsepower.

NOTE: Figures may vary depending upon working conditions. To maintain desired air pressure as nozzle orifice wears, air consumption increases. The effects of nozzle wear on air consumption must be considered when selecting nozzles and the compressors that support them.

When nozzle orifice is 3/8-inch or larger, blast machine valves and piping must be 1-1/4-inch or larger to provide sufficient air volume

Packaging: Boxed individually


Net Orders Checkout

Item Price Qty Total
Subtotal $0.00
Shipping
Total

Shipping Address

Shipping Methods